Pacifica Plus Bottom Paint
Complete Your Purchase
Better for the environment, copper-free Pacifica Plus fights marine growth
Pacifica Plus is designed for those seeking a copper-free antifouling paint and is an excellent choice for use where cuprous oxide-based paints are prohibited. Instead of cuprous oxide, the dual-biocide formula uses copper-free Econea to prevent hard fouling and Biolux® technology to control slime.
With its ablative formula, Pacifica Plus self-polishes as the boat is used. This lowers fuel consumption and helps to reduce the amount of harmful carbon dioxide and sulphur dioxide released into the air. With its high-solids formula, the amount of VOCs released into the air is reduced, providing an additional environmental benefit.
The self-polishing ablative action of Pacifica Plus also reduces paint build-up, along with the need for sanding at haulout. And because Pacifica Plus uses Econea rather than cuprous oxide as its primary biocide, this paint can safely be used on aluminum hulls, outboards, and outdrives without fear of galvanic corrosion.
Key features
- Uses Econea to prevent marine growth
- A copper-free formula is better for the environment
- Ablative formula reduces the need for sanding at haul out
- Available in bright colors
- Dries quickly for same-day launch
- Biolux prevents slime growth
Physical Data
- Vehicle type: Ablative
- Finish: Low sheen
- Available colors: Blue, Green, Red, Black, Grey
- Components: 1
- Curing mechanism: Solvent release
- Solids by Volume: (Theoretical) 65.94%
- Coverage: 528sq. ft. /gal.
- VOC: 330d grams/liter
- Active ingredients: ECONEA 3.9%
- Additives: Biolux
Application
- Application Method: Brush, roller, airless, or conventional spray
- Number of coats recommended: 2-3, Minimum per season, with additional coats for extended service. Bare wood: 3 coats
- Wet Film Thickness: 3 mils/coat
- Dry Film Thickness: 2 mils/coat
- Applicator: High-quality short nap roller (maximum 3/8” nap)
- Application temperature Min. /Max. Range: 5°C/41°F and maximum 35°C/95°F.
- Thinner: 216, Model 117598, or brush ease, Model 203679
Drying Times*(Hours)
| Drying | @41°F | @50°F | @73°F | @95°F |
|---|---|---|---|---|
| To touch | 6 hr. | 3 hr. | 2 hr. | 1 hr. |
| To recoat | 12 hr. | 6 hr. | 4 hr. | 2 hr. |
| To launch | 18 hr. | 9 hr. | 6 hr. | 4 hr. |
Get the right amount of paint:
| Boat Type | Bottom Paint |
|---|---|
| 10' Dinghy | 1 qt. |
| 14' Outboard | 1-2 qt. |
| 18' Runabout | 2 qt. |
| 20' Sailboat | 3 qt. |
| 24' Runabout | 3-4 qt. |
| 30' Sailboat | 1.5 gal. |
| 32' Cruiser | 1.5-2 gal. |
| 36' Auxiliary | 2 gal. |
| 40' Cruiser | 2.5 gal. |
| 45' Sailboat | 3-3.5 gal |
| 50' Sportfisher | 4+ gal. |
Another way to determine bottom paint quantity is to estimate the approximate surface area of the hull below the waterline, using the following formula:
Length x Beam x .75 = Approximate underwater surface area in square feet.
Each paint has a “theoretical coverage” area, but most paints require at least two coats, so you can expect actual coverage to be no greater than half of the theoretical value.
More information
For detailed application instructions and to view available colors, refer to the Pacifica Plus Data Sheet. NOTE: Manufacturer data sheets are subject to revision. Linked data sheets are believed to be accurate at the time of publication.
You May Also Like
